iConverter 100Fx/Tx

100BASE-TX to 100BASE-FX Managed Ethernet Media Converter

The iConverter 100Fx/Tx managed media converters are members of the modular iConverter product family, and provide 100BASE-TX UTP to 100BASE-FX fiber conversion. The iConverter 100Fx/Tx models are available with multimode, single-mode and single-fiber options. They support ST, SC and LC connectors. The UTP port supports 100BASE-TX in either Full or Half-Duplex mode.

question

The iConverter 100Fx/Tx is an IEEE 802.3 compatible 100BASE-TX UTP to 100BASE-FX fiber converter

  • Supports multimode, single-mode, and single-fiber with ST, SC and LC connectors
  • UTP port supports Full or Half-Duplex 100Mbps Ethernet
  • UTP crossover switch eliminates the need for a crossover cable
  • User-selectable link fault detection modes facilitate quick fault detection, isolation and reporting
  • Management is available with the addition of a management module to the chassis
  • SNMP management via NetOutlook® provides real-time port and module information, remote parameter configuration and trap notification
  • Modules are hot-swappable in 19-Module, 5-Module, 2-Module or 1-Module chassis
  • LED displays for immediate visual status of each port
  • Lifetime Warranty and free 24/7 Technical Support

 

The iConverter 100Fx/Tx managed media converters are members of the modular iConverter product family, and provide 100BASE-TX UTP to 100BASE-FX fiber conversion.

The iConverter 100Fx/Tx models are available with multimode, single-mode and single-fiber options. They support ST, SC and LC connectors. The UTP port supports 100BASE-TX in either Full or Half-Duplex mode. A UTP crossover switch eliminates the need for a crossover cable and facilitates connectivity to network equipment such as hubs, switches and workstations.

The 100Fx/Tx features user-selectable Link Propagate, Link Segment, Remote Fault Detection and Symmetrical Fault Detection modes to facilitate quick fault detection, isolation and reporting.

iConverter 100Fx/Tx modules are hot-swappable and can be mounted in a 19-Module (2U high) or 5-Module (1U high) rack-mountable chassis (19-inch or 23-inch) with any combination of redundant AC, 24VDC or 48VDC power supplies. They can also be mounted in a 2-Module AC or 18 to 60VDC powered chassis, or in a 1-Module AC/DC powered chassis.

The iConverter family of managed fiber access media converters are used in Service Provider access networks and Enterprise LANs. iConverter media converters provide fiber connectivity with copper-to-fiber, multimode fiber to single-mode fiber, or dual fiber to single-fiber conversions.

Management is accomplished by using a Network Management Module (NMM2) or a media converter with integrated management (such as an iConverter 10/100M2) that provides monitoring, remote configuration and trap notification. The management module can be accessed via SNMP, Telnet and via a serial port. The SNMP-based management is accomplished via Omnitron's intuitive, graphic-oriented NetOutlook management software or third party SNMP management software. Management via the Telnet and the serial interfaces have an easy-to-use, menu-driven interface.

Some of the real-time 100Fx/Tx parameters that can be monitored include power, link and data receive status. Other parameters include module type and model, hardware and software revisions, serial numbers and a user-defined identifier.

The user can override the 100Fx/Tx module's physical DIP-switch settings by using SNMP or Telnet to remotely configure DIP-switch-selectable parameters such as Link Propagate, Link Segment, Remote Fault Detection and Symmetrical Fault Detection.

In addition to all standard iConverter SNMP traps such as module insertion and removal, the 100Fx/Tx modules can generate traps on port state changes including link-up and link-down. Trap monitoring of specific events can be selectively enabled or disabled by the network administrator.

Model Type 100Fx/Tx
Protocols 100BASE-FX, 100BASE-TX
Copper Connectors RJ-45
Fiber Connectors SC, ST, LC, Single-Fiber SC
Controls UTP X-over, LS/LP, RFD, SFD UTP FDX/HDX, UTP A/N
LED Displays Power, FO link, UTP link, Auto, FDX/HDX
Dimensions W:0.85" x D:4.5" x H:2.8"
Weight 8 oz.
Compliance UL, CE, FCC Class A, NEBS Level 3
Power Requirement 0.7A @ 3.3VDC (typical)
Temperature Standard: 0 to 50º C
Wide: -40 to 60º C
Storage: -40 to 80º C
Humidity 5 to 95% (non-condensing)
Altitude -100m to 4000m
MTBF (hrs) 730,000
Model TypeFiber Media TypeDistancesConnector TypeTx λ (nm)Rx λ (nm)Min.
Tx Power (dBm)
Max.
Tx Power (dBm)
Min.
Rx Sense (dBm)
Max.
Rx Sense (dBm)
Link Budget
(dBm)
STSCLC
100Fx/Tx Dual Fiber MM 5km 8360-0 8362-0 - 1310 1310 -24 -14 -31 -14 7
SM 30km 8361-1 8363-1 8367-1 1310 1310 -15 -8 -31 -8 16
SM 60km 8361-2 8363-2 8367-2 1310 1310 -5 0 -31 -3* 26
SM 120km - 8363-3 8367-3 1550 1550 -5 0 -31 -3* 26
100Fx/Tx Single-Fiber SM 20km - 8370-1 - 1310 1550 -15 -5 -30 -3 15
SM 40km - 8370-2 - 1310 1550 -8 0 -30 -3* 22
SM 20km - 8371-1 - 1550 1310 -15 -5 -30 -3 15
SM 40km - 8371-2 - 1550 1310 -8 0 -30 -3* 22

For wide temperature (-40 to 60º C), add a "W" to the end of the model number. Consult factory for extended temperature (-40 to +75º C) models. When using single-fiber (SF) media converter models, the Tx wavelength on one end has to match the Rx wavelength on the other.
*A minimum of 3dB of attenuation is required for these models.
Consult the factory for additional fiber configurations.

Chassis and Mounting Options Ordering Table

 19-Module5-Module2-Module1-Module
ConfigurationAC
(60 watts)
AC
(120 watts)
24VDC48VDCAC24VDC48VDCAC18-60DCUS ACUNIV AC
One (1) Power Supply 8200-1 8201-1 8206-1 8205-1 8220-1 8226-1 8225-1 8230-0 8235-0 8240-1 8240-2
One (1) Power Supply with Dying Gasp Support - - - - - - - 8230-1 8235-1 8241-1 8241-2
Two (2) Power Supplies 8200-2 8201-2 8206-2 8205-2 8220-2 8226-2 8225-2 - - 8245-111* 8245-112*
Three (3) Power Supplies 8200-3 8201-3 8206-3 8205-3 - - - - - - -
Spare Power Supply 8200-9 8201-9 8206-9 8205-9 8220-9 8226-9 8225-9 - - - -
23" Rack Mounting Kit 8091-2 8091-2 8091-2 8091-2 8092-2 8092-2 8092-2 - - - -
Blank Module Panel 8090-0 8090-0 8090-0 8090-0 8090-0 8090-0 8090-0 8090-0 8090-0 - -
Wall Mounting Hardware Kit -   - - - - - 8249-0 8249-0 8249-0 8249-0
1U 19" Rack Mount Shelf - - - - - - - 8260-0 8260-0 8260-0 8260-0
DIN Rail Mounting Kit -   - - - - - - - 8250-0 8250-0

When ordering a Wide Temperature chassis, add a W to the end of the part number. For example:8230-1W
Consult factory for extended temperature (-40 to +75º C) models.
* Click on part number for complete ordering information on the 1-Slot Redundant Power Chassis with Power over Ethernet

(*) Required field

1000 characters left
Add files