OmniConverter® 10GPoEBT/Sx

Unmanaged 6 Port 60/100W IEEE 802.3bt 10Gigabit Ethernet Switches


  • Unmanaged IEEE 802.3bt compliant 6 Port 1/10G 60W and 100W PoE Ethernet Switches
  • Two 1/10G SFP/SFP+ transceiver uplink ports
  • Supports copper and fiber SFP transceivers
  • Support speeds of 10M, 100M, 1G and 10Gbps using copper SFP/SFP+ transceivers
  • Four 10/100/1000 copper 60W or 100W PoE user ports
  • DC models provide full PoE power simultaneously to all RJ-45 user ports
  • Supports jumbo frames up to 10,240 bytes
  • Configurable PoE Power Reset
  • Uplink redundancy
  • Dual Device mode for operating as two separate switches
  • Directed Switch mode to prevent port flooding
  • Available with AC to DC power adapters or DC terminal block
  • Wall, Rack and DIN-rail mountable
  • Fan-less design
  • Commercial (0º to 50ºC), wide (-40º to 60ºC) and extended (-40º to 75ºC) operating temperature ranges
  • TAA, BAA and NDAA compliant, and Made in the USA
  • Free 24/7/365 Technical Support


The OmniConverter 10GPoEBT/Sx are unmanaged Ethernet switches that feature two 1/10G uplink ports and four 10/100/1000 RJ-45 copper Power Sourcing Powerover-Ethernet user ports. The 10GPoEBT/Sx available with 60W or 100W (IEEE 802.3bt) per user port.

The OmniConverter PoE switches are Layer 2 Ethernet switches that forward frames to any port based on their MAC address.

All models support Directed Switch mode, which directs multicast traffic (such as video) only to the appropriate uplink port, preventing multicast traffic from flooding other network ports.

The switches support daisy-chain configurations and redundant uplinks for critical applications that require protection and sub 50ms restoration in the event of an uplink failure.

The switches support Dual Device mode that enables the 10GPoEBT/Sx to operate as two independent and isolated Ethernet switches.

The 10GPoEBT/Sx modes of operation can be configured using easily accessible DIP-switches. Each DIP-switch function is labeled on the side of the OmniConverter for ease of identification and use.

The OmniConverter switches are available with Small Form Pluggable (SFP) transceiver receptacle ports. The SFP ports support 10/100/1000BASE-T, 1000BASE-T and 10GBASE-T copper transceivers. They also support 1G and 10G multimode or single-mode fiber, dual or single-fiber and standard or CWDM wavelengths.

The switches automatically negotiate and deliver the power level required by a Powered Device (PD) partner. Depending on the model of the OmniConverter PoE switch, the switch can deliver up to 60 or 100 Watts of power per user port.

The switches features a Remote PoE Power Reset that can be configured with a DIP-switch. This feature enables the user to remotely power-cycle and reset each PD increasing network reliability, up time and save manpower time and expense by automating the recovery of remote PD equipment.

All models can be wall mounted, rack mounted or DINrail mounted using an optional mounting clips. They are available with an external 100 to 240V AC power adapter or with a DC terminal connector.


Dual Device Mode Application

This Dual Device feature is extremely useful when two isolated networks domains share a single network distribution location.

The example below depicts a scenario where a surveillance security (green) network and a Wi-Fi (purple) network are sharing a single hub distribution location. Using the two uplinks and the Dual Switch mode facilitates using a single PoE switch driving both the Cameras and the Wi-Fi Access Points while maintaining isolation between the networks.

Dual Media Converter Mode OmniConverter 10GPoEBT Sx

Daisy Chain Application

This example demonstrates the daisy chain capabilities of the OmniConverter PoE switches. In this application each OmniConverter switch connects to its neighboring switch via its uplink ports. The daisy chain can continue to additional switches using this method of connectivity.

Each OmniConverter switch provides connectivity to the high speed fiber links, and 802.3bt power to IP cameras and Wi-Fi access points at each location along the daisy chain.

Daisy Chain Application OmniConverter 10GPoEBT Sx


Description OmniConverter® 10GPoEBT/Sx
10/100/1000BASE-T with 1/10G Gigabit Fiber
Unmanaged 6 Port IEEE 802.3bt 60/100W PoE Ethernet Switch
Standard Compliances

IEEE 802.3,

IEEE 802.3af (15.40 watts max),

IEEE 802.3at (30 watts max),

IEEE 802.3bt (60 and 100 watts max)

Regulatory Compliances

Safety*: UL 62368-1,UL 60950-1,

               IEC 62368-1, IEC 60950-1,

               EN 62368-1, EN 60950-1,

               CAN/CSA C22.2 No. 62368-1-14,

               CAN/CSA C22.2 No. 60950-1,

               CE Mark, UKCA

EMC:      EN 55032/24 CE Emissions/Immunity,

               IEC 61000-6-4 Industrial Emissions,

               IEC 61000-6-2 Industrial Immunity

EMI:       CISPR 32,

               FCC 47 Part 15 Subpart B Class A

EMS:      IEC 61000-4-2 ESD: Contact: 6 kV; Air: 8 kV,

               IEC 61000-4-3 RS: 80 MHz to 1 GHz: 10 V/m,

               IEC 61000-4-4 EFT: Power: 2 kV; Signal: 1 kV (DC models),

               IEC 61000-4-4 EFT: Power: 1 kV; Signal: 1 kV (AC models),

               IEC 61000-4-5 Surge: Power: 2 kV; Signal: 2 kV (DC models),

               IEC 61000-4-5 Surge: Power: 1 kV Line/Line; 2 kV Line/Gnd; Signal: 2 kV (AC models),

               IEC 61000-4-6 CS: Signal: 10 V,

               IEC 61000-4-8 (Magnetic Field) 30A/m,

               IEC 61000-4-11 (Voltage Dips, interrupts)

IP Rating: IP20 Protection


Environmental REACH, RoHS and WEEE
PoE Modes IEEE Alternate A (Alt A) and 4-Pair
Frame Size Up to 10,240 bytes
Port Types

Copper:          10/100/1000BASE-T (RJ-45)

SFP/SFP+:    10GBASE-X Fiber Transceivers

                      10GBASE-T Copper Transceivers

                      1000BASE-X Fiber Transceivers

                      1000BASE-T Copper Transceivers

                      10/100/1000BASE-T SGMII Copper Transceivers

Cable Types

Copper: EIA/TIA 568A/B, Cat 5 UTP and higher

Fiber:    Multimode: 50/125, 62.5/125µm

              Single-mode: 9/125µm

AC Power Requirements
(Models with AC/DC Adapters)

100 - 240VAC/50 - 60Hz

3.5A max at 115VAC

2.5A max at 230VAC

Supplied adapter provides 250W

DC Power Requirements
(Models with DC Terminals)

60W Models:

+46 to +57VDC;

4.47A @ 56VDC

2 Pin Terminal (isolated)

100W Models:

+46 to +57VDC;

7.33A @ 56VDC

2 Pin Terminal (isolated)

Dimensions (W x D x H) 6.28” x 5.2” x 1.5” (159.5 mm x 132.1 mm x 38.1 mm)
Weight Module Only: 1.6 lb. (735 grams)
Module with AC/DC Adapter: 3.7 lbs. (1703 grams)
Operating Temperature Commercial: 0 to 50°C
Wide: -40 to 60°C (-20°C AC cold start)
Extended: -40 to 75°C - not available for models with AC/DC power adapter
Storage: -40 to 80°C
Humidity 5% to 95% (non-condensing)
Altitude -100m to 4,000m (operational)
MTBF (hrs) Module Only: 285,000
AC/DC Adapter: 100,000
Warranty 5 year product warranty with 24/7/365 free Technical Support
2 year AC power adapter warranty


AC/DC Adapter Temperature Derating - Total Available Wattage to RJ-45 Ports
Model Watts Required 40°C 50°C 60°C
10GPoEBT/Sx 60W 240 watts Full Power 175 watts 115 watts
10GPoEBT/Sx 100W 400 watts 240 watts 175 watts 115 watts
The AC/DC Adapter Temperature derating table is not applicable to models with DC Terminal (see Ordering table for Direct DC -9 option). The DC Terminal models will provide full PoE power over the operating temperature range of the module as long as the DC input voltage meets the requirements stated in the specification table.


Power / Voltage Requirements and Specifications



IEEE 802.3af PoE


IEEE 802.3at PoE+


(Type 3)


IEEE 802.3bt PoE
(Type 4)

Power Supply Voltage Range 46.0 to 57.0 VDC 51.0 to 57.0 VDC 51.0 to 57.0 VDC 53.0 to 57.0 VDC
Voltage Range at PSE port Output 44.0 to 56.0 VDC 50.0 to 56.0 VDC 50.0 to 56.0 VDC 52.0 to 56.0 VDC
Maximum Power from PoE/PSE port 15.4 watts 30 watts 60 watts 100 watts
Minimum Voltage at PoE/PD port input* 37.0 VDC 42.5 VDC 42.5 VDC 41.1 VDC
Minimum Power at PoE/PD port* 12.95 watts 25.5 watts 51 watts 71 watts
* at 100 meters using Cat5


Step 1: Choose the Base Part Number (xxxxB-x-xx-pt)

OmniConverter 10GPoEBT/Sx Models
Model NumberDescription
3060B-0-24-pt OmniConverter 10GPoEBT/Sx 2 x SFP/SFP+ uplink port and 4 x RJ-45 IEEE 802.3bt 60W user ports
3062B-0-24-pt OmniConverter 10GPoEBT/Sx 2 x SFP/SFP+ uplink port and 4 x RJ-45 IEEE 802.3bt 100W user ports
 Contact Omnitron for other fiber options. Order the appropriate SFPs separately. Visit the Optical Transceivers web page.

Step 2: Choose the Power Option (xxxxB-x-xx-pt)

 1 = External AC/DC Adapter, 100 - 240 VAC included, with US Power Cord 
 2 = External AC/DC Adapter, 100 - 240 VAC included, No Power Cord 
 8 = External AC/DC Adapter, 100 - 240 VAC included, PS JET/PSE Certified, with Japanese Power Cord 
 9 = Direct DC 2 pin terminal connector, no AC/DC power adapter 

Step 3: Choose the Operating Temperature Range Option (xxxxB-x-xx-pt

 <leave blank> = Commercial temperature (0 to 50°C)
 W = Wide temperature (-40 to 60°C)
 Z = Extended temperature (-40 to 75°C) - not available for models with AC/DC Power Adapters 



Model NumberDescription
8251-0 DIN-Rail Mounting Clip
8260-0 19" rack mount shelf


pdf OmniConverter 10GHPoEBT/Sx (Data Sheet) (856 KB)

pdf OmniConverter 10GPoEBT/Sx (Quick Start) (950 KB)