OmniConverter® 10G/M

Managed 6 and 10 Port 10Gigabit Ethernet Switch



Features


  • Managed 1/10G Ethernet Switch
  • Two 1/10G SFP/SFP+ transceiver uplink ports
  • Supports copper and fiber SFP transceivers
  • Supports 10M, 100M, 1G and 10Gbps copper SFP/SFP+ transceivers
  • Four or eight 10/100/1000 copper user ports
  • Supports jumbo frames up to 10,240 bytes
  • Management via Web, Telnet, SSH, SNMPv1/v2c/v3 and serial interfaces
  • Easy to use Hierarchical Command Line Interface
  • SNMP management via Omnitron’s NetOutlook® management software, or third-party SNMP software
  • Supports IPv4 and IPv6 addressing
  • IEEE 802.1x, RADIUS, TACACS+ and ACL
  • Email Notification
  • Rapid and Multiple Spanning Tree Protocol
  • IEC 62439-2 Industrial Ring Media Redundancy
  • IEEE 802.1ax LAG and LACP; Active/Active and Active/Standby
  • Dual Device mode for operating as two separate switches
  • Directed Switch mode AKA Camera mode to prevent port flooding
  • AC to DC Power Adapter or 2-Pin DC terminal
  • Commercial (0º to 50ºC), wide (-40º to 60ºC) and extended (-40º to 75ºC) operating temperature ranges
  • TAA, BAA and NDAA compliant, and Made in the USA
  • Free 24/7/365 Technical Support

ADDITIONAL FEATURES

  • IEEE 802.1Q VLAN tagging and IEEE 802.1ad Q-in-Q
  • Port Access Control for enhanced security
  • Broadcast / Multicast / Unicast Storm Prevention
  • DHCP Relay Option 82, DHCPv6 and DHCPv6 Relay
  • IPv4 Internet Group Management (IGMP) and IPv6 Multicast Listener Discovery (MLD) snooping
  • Rate Limiting, Queue prioritization and Class of Service
  • IEEE 802.1ab Link Layer Discovery Protocol
  • Static MAC configuration and blocking of unknown Unicast/Multicast addresses
  • SNTP / NTP and time of day
  • Wall, Rack and DIN-rail mountable




Description


The OmniConverter 10G/M is a managed compact Ethernet switch that features two 1/10G uplink ports and four or eight 10/100/1000 RJ-45 copper user ports. The OmniConverter 10G/M enables network distance extension with fiber or copper cabling.

The OmniConverter 10G/M is a Layer 2 Ethernet switch that forwards frames to any port based on their MAC address.

The OmniConverter 10G/M supports Directed Switch mode, which directs multicast traffic (such as video) only to the appropriate uplink port, preventing the multicast video traffic from flooding other network ports.

The switches support redundant uplinks, industrial ring Media Redundancy Protocol (MRP), Spanning Tree protocol and daisy-chain configurations for high availability industrial network applications.

The switches support Dual Device mode that enables the 10G/M to operate as two independent and isolated Ethernet switches. In Dual Device mode, the 10G/M provides separate and independent data traffic paths between each uplink port and a group of user ports.

The mode of operation can be configured using easily accessible DIP-switches or using Web, Telnet, SSH, SNMPv1/v2c/v3 or Serial Console management interfaces. IPv4 and IPv6 are supported on the switches. These management interfaces provide access to filtering and security options, such as, broadcast storm prevention, IGMP, IEEE 802.1x, RADIUS, TACACS+ and Access Control Lists. Email notification and alarm reporting is provided.

The OmniConverter switches are available with Small Form Pluggable (SFP) transceiver receptacle ports. The SFP ports support 10/100/1000BASE-T, 1000BASE-T and 10GBASE-T copper transceivers. They also support 1G and 10G multimode or single-mode fiber, dual or single-fiber and standard, CWDM and DWDM wavelengths.

The compact OmniConverter 10G/M Ethernet switches can be wall mounted, rack mounted using a shelf or DIN-rail mounted using DIN-rail mounting clips. The OmniConverter Ethernet switch models are available with 2-Pin DC Terminal or external 100-240V AC power adapters.





Examples


Dual Device Mode Application

This Dual Device feature is extremely useful when two isolated networks domains share a single network distribution location.

The example below depicts a scenario where the Administration (green) network and the Engineering (purple) network are sharing a single hub distribution location. Using the two uplinks and the Dual Switch mode facilitates using a single switch driving both the Administration and the Engineering workstations while maintaining isolation between the networks.

Dual Media Converter Mode 2900 10g m

Daisy Chain Application

This example demonstrates the daisy chaining and ring capabilities of the OmniConverter. In this application each OmniConverter switch connects to its neighboring switches via its uplink ports eventually closing the ring. The OmniConverter switches are providing connectivity between the workstations and the router.

Using this network architecture combined with ring protection protocols such as Media Redundancy Protocol (MRP) or Rapid Spanning Tree Protocol (RSTP) facilitates a highly resilient network required in mission critical applications.

Dasiy Chain Application 2900 10g m





Specifications


Description OmniConverter® 10G/M
10/100/1000BASE-T with 1/10G Uplink Ports
Managed 6 and 10 Port 10Gigabit Ethernet Switch
Standard Compliances

IEEE 802.3, IEEE 802.1Q, IEEE 802.1ad, IEEE 802.1ab, IEEE 802.1ax, IEEE 802.1w RSTP/MSTP

RFC 5424, RFC 4541, RFC 2710, IEC 624339-2, SMTP, SNTP, RADIUS, TACACS+, IEEE 802.1x

Regulatory Compliances
(*Pending)

Safety*: UL 62368-1, UL 60950-1,

              IEC 62368-1, IEC 60950-1,

              EN 62368-1, EN 60950-1,

              CAN/CSA C22.2 No. 62368-1-14, CAN/CSA C22.2 No. 60950-1,

              CE Mark,

              UKCA

EMC:     EN 55032/24 CE Emissions/Immunity,

              IEC 61000-6-4 Industrial Emissions, IEC 61000-6-2 Industrial Immunity

EMI:      CISPR 32,

              FCC 47 Part 15 Subpart B Class A

EMS:     IEC 61000-4-2 ESD: Contact: 6 kV; Air: 8 kV,

              IEC 61000-4-3 RS: 80 MHz to 1 GHz: 10 V/m,

              IEC 61000-4-4 EFT: Power: 2 kV; Signal: 1 kV (DC models),

              IEC 61000-4-4 EFT: Power: 1 kV; Signal: 1 kV (AC models),

              IEC 61000-4-5 Surge: Power: 2 kV; Signal: 2 kV (DC models),

              IEC 61000-4-5 Surge: Power: 1 kV Line/Line; 2 kV Line/Gnd; Signal: 2 kV (AC models),

              IEC 61000-4-6 CS: Signal: 10 V, IEC 61000-4-8 (Magnetic Field) 30A/m,

              IEC 61000-4-11 (Voltage Dips, interrupts)

IP Rating: IP20 Protection

ACT: TAA, BAA,NDAA

Environmental REACH, RoHS and WEEE
Management

IPv4 and IPv6 address

Web, Telnet, SSH, SNMPv1/v2c/v3

In-Band management via Ethernet port

Out-of-band management via serial port

Frame Size Up to 10,240 bytes
Port Types

Copper:       10/100/1000BASE-T (RJ-45)

SFP/SFP+: 10GBASE-X Fiber Transceivers

                   10GBASE-T Copper Transceivers

                   1000BASE-X Fiber Transceivers

                   1000BASE-T Copper Transceivers

                   10/100/1000BASE-T SGMII Copper Transceivers

Serial:         RS-232 (RJ-45)

Cable Types

Copper: EIA/TIA 568A/B, Cat 5 UTP and higher

Fiber:     Multimode: 50/125, 62.5/125µm

              Single-mode: 9/125µm

Serial:    Category 3 and higher

AC Power Requirements
(Models with AC/DC Adapters)

100 - 240VAC/50 - 60Hz

0.25A max at 115VAC

0.12A max at 230VAC

DC Power Requirements
(Models with DC Terminals)

4 RJ-45 Ports:

+12 to +57VDC;

0.81A @ 12VDC

0.20A @ 48VDC

2 Pin Terminal (isolated)

8 RJ-45 Ports:

+12 to +57VDC;

0.90A @ 12VDC

0.22A @ 48VDC

2 Pin Terminal (isolated)

Dimensions
(W x D x H)
6.28” x 5.2” x 1.5” (159.5 mm x 132.1 mm x 38.1 mm)
Weight

4 RJ-45 Ports:

Module Only: 1.5 lb. (720 grams)

Module with AC/DC Adapter: 2.0 lbs. (913 grams)

8 RJ-45 Ports:

Module Only: 1.6 lbs. (748 grams)

Module with AC/DC Adapter: 2.1 lbs. (941 grams)

Operating Temperature Commercial: 0 to 50°C
Wide: -40 to 60°C (-20°C AC cold start)
Extended: -40 to 75°C (-20°C AC cold start) 
Storage: -40 to 80°C
Humidity 5% to 95% (non-condensing)
Altitude -100m to 4,000m (operational)
MTBF (hrs) Module Only: 290,000
AC/DC Adapter: 100,000
Warranty 5 year product warranty with 24/7/365 free Technical Support
2 year AC power adapter warranty




Ordering


Step 1: Choose the Base Part Number (xxxx-x-xx-pt)

OmniConverter 10G/M Models
Model NumberDescription
2900-0-24-pt OmniConverter 10G/M 2 x SFP/SFP+ uplink port and 4 x RJ-45 user ports
2900-0-28-pt OmniConverter 10G/M 2 x SFP/SFP+ uplink port and 8 x RJ-45 user ports
Contact Omnitron for other fiber options. Order the appropriate SFPs separately. Visit the Optical Transceivers web page.

Step 2: Choose the Power Option (xxxx-x-xx-pt)

 1 = External AC/DC Adapter, 100 - 240 VAC included, with US Power Cord
 2 = External AC/DC Adapter, 100 - 240 VAC included, No Power Cord 
 8 = External AC/DC Adapter, 100 - 240 VAC included, PS JET/PSE Certified, with Japanese Power Cord
 9 = Direct DC 2 pin terminal connector, no AC/DC power adapter

 Step 3: Choose the Operating Temperature Range Option (xxxx-x-xx-pt

<leave blank> = Commercial temperature (0 to 50°C)
 W = Wide temperature (-40 to 60°C) 
 Z = Extended temperature (-40 to 75°C) 

 

Accessories

Model NumberDescription
8251-0 DIN-Rail Mounting Clip
8260-0 19" rack mount shelf




Documents


pdf OmniConverter 10G/M (Data Sheet) (856 KB)

pdf OmniConverter 10G/M (Quick Start) (1.26 MB)

 

pdf OmniConverter Command Line Interface (User Manual) (1.71 MB)

pdf OmniConverter Web Interface (User Manual) (8.48 MB)

pdf OmniConverter / RuggedNet 2.5 Hierarchical CLI (User Manual) (1.71 MB)