1000BASE-T to 1000BASE-SX/LX Managed Media Converter

*The iConverter Gx modules are not supported in future software releases and are not recommended for new designs or deployments. View the iConverter Gx AN web page.

The iConverter Gx is an IEEE 802.3ab compatible 1000BASE-T UTP to 1000BASE-X fiber converter

• Supports multimode, single-mode and single-fiber
• 1000Mbps UTP port with Half or Full-Duplex auto-negotiation
• UTP auto-crossover feature eliminates the need for a crossover cable
• User-selectable link fault detection modes facilitate quick fault detection, isolation and reporting
• Management is available with the addition of a management module to the chassis
• SNMP management via NetOutlook® provides real-time port and module information, remote parameter configuration and trap notification
• Modules are hot-swappable in 19-Module, 5-Module, 2-Module or 1-Module chassis
• LED displays for immediate visual status of each port
• Lifetime Warranty and free 24/7 Technical Support

The iConverter Gx managed media converters are members of the modular iConverter product family, and provide 1000BASE-T UTP to 1000BASE-X fiber conversion.

The iConverter Gx models are available in multimode, single-mode, and single-fiber options. The Gx supports ST, SC, MT-RJ, and LC connectors. The UTP port supports 1000BASE-T in either Half or Full-Duplex mode. The UTP auto-crossover feature eliminates the need for a crossover cable and facilitates connectivity to network equipment such as hubs, switches and workstations.

The iConverter Gx features user-selectable Link Propagate, Link Segment and Remote Fault Detection modes to facilitate quick fault detection, isolation and reporting.

iConverter Gx modules are hot-swappable and can be mounted in a 19-Module (2U high) or 5-Module (1U high) rack-mountable chassis (19-inch or 23-inch) with any combination of redundant AC, 24VDC or 48VDC power supplies. It can also be mounted in a 2-Module AC or 18 to 60VDC powered chassis, or in a 1-Module AC/DC powered chassis.

The iConverter family of managed fiber access media converters are used in Service Provider access networks and Enterprise LANs. iConverter media converters provide fiber connectivity with copper-to-fiber, multimode fiber to single-mode fiber, or dual fiber to single-fiber conversions.

View an Application Example

Management is accomplished by installing a Network Management Module (NMM2) or a media converter with integrated management (such as an iConverter 10/100M2) in the chassis with the Gx. Management provides monitoring, remote configuration and trap notification. The management module can be accessed via SNMP, Telnet, and via a serial port. The SNMP-based management is accomplished via Omnitron's intuitive, graphic-oriented NetOutlook management software or third party SNMP management software, while the Telnet and the serial interfaces have an easy-to-use, menu-driven interface.

Some of the real-time Gx parameters that can be monitored include power, link and data receive status. Other parameters include module type and model, hardware and software revisions, serial numbers and a user-defined identifier.

The user can override the Gx module's physical switch settings using SNMP or Telnet to remotely configure switch-selectable parameters such as UTP Duplex Mode.

The Gx modules can generate SNMP traps for module insertion or removal, and port state changes including link-up and linkdown. Trap monitoring of specific events can be selectively enabled or disabled by the network administrator.

For wide temperature (-40 to 60º C), add a "W" to the end of the model number.
Consult factory for extended temperature (-40 to +75º C) models.
When using single-fiber (SF) media converter models, the Tx wavelength on one end has to match the Rx wavelength on the other.
*A minimum of 3dB of attenuation is required for these models.
¹ 62.5/125μm, 100/140μm multimode fiber up to 220m. 50/125μm multimode fiber up to 550m. Refer to the fiber cable manufacturer for multimode distance specifications.